Owalo 7000 pendant lamp:
Tranquil balance

A horizontal pendant that lights up both meeting rooms and dining areas. Comes with the latest in LED technology.

Colour:

Get it here!

Secto Design Owalo 7000 - Tranquil balance

Watch video

Secto Design Owalo 7000 pendant lamp

Owalo 7000. Hotel Valo & Work. Helsinki, Finland. Photo by Uzi Varon

Owalo 7000. Design Dock, Helsinki Design Week. Photo by Uzi Varon

Owalo 7000. Locker & Légere Hotelbetriebs, St. Ruprecht / Raab, Austria. Photo by Markus Kaiser

Owalo 7000. Actavis Baltics Office, Vilnius, Lithuania. Design by Arch. Ruta Bagdzeviciute. Photo by Dualhead

More images of the Owalo 7000 pendant lamp here

Owalo 7000 pendant lamp

Handmade of PEFC-certified form pressed birch in Finland by highly skilled craftsmen. Uses the latest LED-technology.

Finishing options

Shade	Case	Cable	Ceiling cup
Natural birch	White	White	White
White laminated	White	White	White
Black laminated	Black	Black	Black
Walnut veneer	White	White	White

Product details

Material	Form pressed birch slats, fine textured powder coated steel case, acrylic diffuser
Dimensions	Height 13 cm Length 100 cm Width 9 cm Weight 3,1 kg Package 119 × 22 × 18 cm, 5,1 kg
Voltage	100-240V 50/60Hz
Light source	A built-in LED, 21 W, 2850 K, 2500 lm, CRI 85. This product contains a light source of energy efficiency class D.
Dimming	Details
Cable	200 cm, textile cable, connector (+ a separate ceiling plug in Finland and Sweden), ceiling cup, 2 steel wires
Classification	Ingress Protection IP20, IEC Protection Class II, CE marking
Installation	Separate instructions on the website.
Maintenance	Wipe dust regularly. To remove fresh stains wipe with a slightly damp cloth.

NOTE: Built-in step dimming. The lamp can be dimmed (to 70 %, 30 % and 15 %) by clicking the wall switch.

WARNING: The cable or light source can only be replaced by the manufacturer or an authorized service agent.

Assemble the cable holder

Step 1	Be sure to insert the wire into the holder at least far enough to be able to clearly see it protrude from the other end of the holder. When attaching the holder into concrete or stone, use a screw anchor.
Step 2	Push the wire sleeve to free the wire lock.
Step 3	Cut off the extra wire.
Step 4	Wire exit angle may not exceed 10°.

Connect and adjust the balance

Step 5	Hold the lampshade. Push the wire sleeve to lower it down. Push the wire sleeve to free the wire lock.
Step 6	Hold the lampshade. Pull the wire to raise it up.
Step 7	Cut off the extra wire.
Step 8	Cable straightener: Adjust position and tighten the screw.

Dezall lamptops

This Secto Design pendant uses the patented ceiling suspension by Dezall. Easy and quick to install, enables the ceiling cup to sit perfectly tight against the ceiling.

Step 1	Lock the cord in the upper part of the screw, start in the middle. Then insert it into the opening along the thread. Push it down into the bottom of the channel.
Step 2	Insert the screw, plug and remaining cord through the cover from below. Also insert it through the ring if this is to be used.
Step 3	Put the two matching bottom parts together, facing each other, around the cord between the cover and the lamp. Insert the assembled bottom part into the cover by fitting the “wings” into the slots inside the cover. Push it into the cover until fully seated.
Step 4	Hang the screw on the ceiling hook and connect the plug.
Step 5	Move the lamptop upwards towards the screw hanging on the hook. When the screw and the bottom parts’ “nut” have come in contact inside the cover, start screwing the cover clockwise until it reaches the ceiling.
Step 6	The lamptop is now sitting straight to the ceiling.

Round ceiling cup

Height	8,1 cm / 8,9 cm (with ring)
Outer upper	Ø 11,7 cm / 12,0 cm (with ring)
Inner upper	Ø 11,2 cm / 11,7 cm (with ring)
Weight	58 g / 74 g (with ring)
Color	White or black matt soft lacquer depending on the colour of the pendant
Information	The round ceiling cup includes an additional ring, which enables leading the cable along the ceiling into the ceiling cup. The additional ring can also be used to cover a larger ceiling socket. Any extra length of the cable can be swirled into the ceiling cup when altering the hanging height of the pendant.